Freezing Biological Samples

Neuroscience researchers usually need to see slices of whole brain in order to determine the location in brain of detail they are viewing under the microscope. The brain needs to be hardened to allow cutting the thin slices, unless a vibrating blade microtome, which is much slower, is used. Paraffin embedding as commonly used for medical samples works only for small or thin samples, paraffin will not penetrate to the center of a whole rodent brain. Thus, neuroscience researchers usually use freezing to harden the brain tissue for sectioning.

Get Knowledge Pathway updates delivered directly to your inbox.

If you have viewed this educational webinar, training or tutorial on Knowledge Pathway and would like to apply for continuing education credits with your certifying organization, please download the form to assist you in adding self-reported educational credits to your transcript.

Apply for self-reported educational credits

Three solid forms of water

Freezing damages cell membranes, and reduces the histological readability of biological specimens. This is a discussion of why, the consequences, and how to minimize or avoid the damage when using freezing as the means to harden biological tissue in order to cut thin sections for histology.

Pure water can exist in the solid state in three forms. There are two crystalline forms, hexagonal crystal, and cubic crystal.  Water can also be frozen so rapidly it does not have time to form crystals, and remains amorphous (vitreous form). Crystal formation is responsible for the expansion of water as it freezes (expansion on freezing is a property unique to water), so vitreous ice does not expand upon solidification. This makes it the only desirable form of freezing for biological specimens.

Rate of freezing critical

Expansion of the water content by freezing stretches and penetrates cell membranes. Slow freezing promotes ice crystal formation, and thus expansion. Biological materials are poor thermal conductors. It is therefore likely that thermal gradients will exist as the sample is frozen, and some ice crystals will form in the interior of any piece of tissue over 10 mm from the cold source. Placed on a cold surface to freeze, specimens will freeze slowly and will thus likely form crystals, especially in parts most distal from the freezing surface. When sectioned, slowly frozen tissue with large crystal formation will have the well known “swiss cheese” effect, multiple holes and lost cell contents, to varying degrees, depending on the degree and size of crystal formation.

Note that it is the rate of freezing, not the end-temperature, that is critical at first. Fast freezing depends on the percentage of the total surface in contact with the cold source, the volume of water, the starting temperature of the water (specimen), and how cold the source is. Ideally, the cold source is at an extremely cold temperature and arranged to contact all surfaces. 

Fig. 1: Ice crystal artifact in a section of skeletal muscle
Fig. 2: Frozen section "shutters" caused by sectioning a block thar was too cold
Fig. 3: Layers of dense vitreous ice. Source:

Sectioning as soon as possible

However, even if a specimen is successfully quick frozen as vitreous, it may not stay that way. Vitreous ice is an unstable state. At above -121˚C, amorphous ice begins to gradually restructure as cubic ice, and expand.  At above -80˚C, cubic ice begins to restructure as hexagonal ice, and expands again. Fortunately, this is a slow conversion process, depending on temperature gradients, and purity of the water. 

In most common applications, tissue must be warmed above the snap freezing temperature in order to section it (-9 to -19˚C for brain, but depending on the tissue type). Otherwise it is too cold to cut, and shatters when bent by the knife bevel. The visible symptom of cutting too cold is “shutters” or shatter marks parallel to the knife blade. The sectioning should begin as soon as the tissue is warm enough to cut. Tissue should never be left overnight or for long periods in a cryostat, even if there is no defrost cycle. The conversion from vitreous ice to large hexagonal crystals will begin. Crystals will expand the ice, and damage cells.

Liquid nitrogen

To freeze most quickly, immersion in a liquid creates the most surface contact. An acceptable second is to place on a prechilled metal pedestal, and quickly surround the tissue with powdered dry ice, powdered to maximize surface contact.

Liquid nitrogen is one of the coldest liquids routinely available.  It does not mix with tissue. These properties would seem to make it an ideal freezing medium. However, liquid nitrogen has an extremely low specific heat constant. The result is that it boils locally and copiously at the contact point with even a small piece of warmer tissue. One consequence is that a vapor barrier, a layer of nitrogen gas, can build up next to the tissue, and insulate and greatly slow penetration of cold into the tissue, and thus slow the rate of freezing in an unpredictable pattern. As a result, it often happens that the outer layer of tissue is quick frozen and vitreous, but then the vapor barrier is formed, cold penetrates more slowly, and the inner part freezes slower.  Crystal formation expands the tissue inside the frozen shell, and the entire block cracks. A cracked block indicates that at least the innermost tissue has been frozen crystalline. Note that this is a problem with large blocks of tissue (for example, a whole rat or even mouse brain), but liquid nitrogen works very well to freeze biopsy or smaller samples, and is used successfully in clinical histology labs.

Other solutions

Various other liquids are used more reliably for larger blocks, most notably isopentane cooled to -80˚C. It does not form vapor barriers, and if the tissue is little more than a cubic centimeter, it will freeze as all vitreous. Full immersion in the liquid is necessary for maximum surface contact, and harmless to the tissue. Movement through the liquid is helpful.

Another solution is to permeate or perfuse the tissue with glycerine, polyethylene glycol (antifreeze), glycerol, or sucrose solutions. These will disrupt crystal formation, and lower the freezing temperature. Sucrose at 30% in phosphate buffer is commonly used, but only with well fixed tissue, after fixation, as the osmolarity would shrivel unfixed tissue.


本記事は、原文が英語の記事の翻訳であり、英語版と日本語版に何らかの齟齬があった場合、 英語版が優先するものといたします。

ライカバイオシステムズの「Knowledge Pathway」の記事や文書、その他一切のコンテンツは、 ライカバイオシステムズのウェブサイト 利用規約 の対象となります。ウェビナー、 トレーニングプレゼンテーションおよび関連資料を含むすべてのコンテンツは、 医療専門家が関心のある特定の主題に関する一般的な情報を提供することを目的としており、 医療、規制、または法律上のアドバイスを意図しておらず、解釈されるべきではありません。 第三者のコンテンツで表明された見解および意見は、話者/著者の個人的な見解および意見を反映するものであり、 必ずしもライカバイオシステムズとその従業員または代理人の見解ないし意見を表する、もしくは反映するものではありません。 コンテンツに含まれる第三者のリソースまたはコンテンツへのリンクは、便宜上においてのみ提供されています。 製品の使用については、製品情報ガイド、添付文書、操作マニュアルなど、該当する製品のドキュメントを参照してください。

ライカバイオシステムズおよび編集者は、記事や文書、一切のコンテンツに記載されている 薬物、デバイス、技術、または手順の使用から直接または間接的に生じるいかなる法的責任も負わないものとします。

Copyright © 2021 Leica Biosystems division of Leica Microsystems, Inc. and its Leica Biosystems affiliates. All rights reserved. LEICA and the Leica Logo are registered trademarks of Leica Microsystems IR GmbH.

Want us to feature your writing?

We are looking for more great writers to feature here. Send us a submission and we'll be in touch!

Send your Writing!

Like what you see?

Get more Knowledge Pathway content like this delivered directly to your inbox. Unsubscribe at any time.